1SP0340V2M0-FZ1200R45HL3
Single-Channel SCALE-2 Plug-and-Play for 4.5kV IGBTs, Direct Paralleling Supported by Master/Slave Drivers
Product Details
The new 1SP0340 SCALE-2 Plug-and-Play driver is specifically designed for the reliable and safe driving of 130 x 140 mm and 190 x 140 mm IGBT modules with 6000 V isolation voltage and 4.5 kV blocking voltage. It is optimized for high-reliability applications in the rail industry.
The driver concept relies on a master/slave principle that enables parallel-connected IGBT modules to be operated safely. The master (1SP0340V) can be used as a stand-alone driver without slave to drive a single IGBT module, or with up to three slaves (1SP0340D) to drive up to four parallel-connected IGBT modules.
The master is equipped with a fiber-optic interface and global fault management. In master/slave configurations, the slaves are connected to the master via a bus cable which distributes the common command signal and the secondary-side supply voltages from the DC/DC converter.
The 1SP0340 driver is based on the highly-integrated SCALE-2 chipset which enables high-performance, complete and extremely-compact single-channel IGBT drivers.
The SCALE-2 chipset also reduces the component count by 80% when compared to conventional solutions, thus significantly increasing reliability and reducing costs.
1SP0340 drivers are equipped with Dynamic Advanced Active Clamping (DA2C), short-circuit protection, regulated turn-on gate driving voltage and supply-voltage-monitoring.
Tightly-matched driver versions are available for all mechanically-compatible IGBT modules. Plug-and-play capability enables immediate operation after mounting, and the user needs to invest no effort adjusting or designing-in the driver for a specific application.
Fiber-Optic Interface Options
Fiber-optic links are used to electrically isolate the command and status-feedback signals.
For details, please check the product documentation.
Power supply and electrical isolation
In contrast to other SCALE-2 plug-and-play drivers, the 1SP0340 driver is modular, so the driver card and power supply (ISO5125I DC/DC converter) are two separate units. This means that any driver that has been developed to match a specific IGBT module can be used for any required isolation specification. Only the separate power supply (ISO5125I) must be selected to match the specific application. A further benefit is that drivers for 4.5 kV IGBTs can be implemented in 2-level, 3-level and multi-level inverter topologies.
The driver is mounted directly onto the IGBT module using three screws. The separate power supply unit is attached close by the IGBT. For parallel-connected drivers, only one power supply is needed per switch.
Specifications
Supported Module(s) | FZ1200R45HL3 |
Max Switching Frequency | 3.50 kHz |
IGBT Voltage Class | 4500 V |
Technology | SCALE-2 |
Power - Output/Channel (Max) | 2.80 W |
Interface Type | Fiber Optic |
IGBT Manufacturer | Infineon |
Number of Channels | 1 |
Gate Peak Current (Max) | +35 A |
Product Type | Board |
Product Sub-Type | PnP Driver |
Supported Module Type | IGBT |
Main/Peripheral | Main |
Supported Topologies |
2-level Voltage Source
3-level NP-Clamped - Type 1
3-level NP-Clamped - Type 2
Multi-Level NP-Clamped
|
Protection Features |
Dynamic Adv Active Clamping
Over-voltage
Short Circuit
UVLO(Sec-side)
|
Driving Mode | Direct-Independent |
Connection Type to IGBT | Direct |
Supply Voltage (Typ) | 25.00 V |
Gate Turn-on Voltage | +15.00 V |
Gate Turn-off Voltage | --10.00 V |
Voltage - DC Link Off state (60s) | 3550.00 V |
Time - Output Rise | 10.00 ns |
Time - Output Fall | 25.00 ns |
Gate Peak Current (Min) | -35 |