솔루션 찾기 기술 지원

1SP0340D2S0-CM1500HC-90XA

Single-Channel SCALE-2 Plug-and-Play for 4.5kV IGBTs, Direct Paralleling Supported by Master/Slave Drivers

애플리케이션

제품 상세 정보

The new 1SP0340 SCALE-2 Plug-and-Play driver is specifically designed for the reliable and safe driving of 130 x 140 mm and 190 x 140 mm IGBT modules with 6000 V isolation voltage and 4.5 kV blocking voltage. It is optimized for high-reliability applications in the rail industry. 

The driver concept relies on a master/slave principle that enables parallel-connected IGBT modules to be operated safely. The master (1SP0340V) can be used as a stand-alone driver without slave to drive a single IGBT module, or with up to three slaves (1SP0340D) to drive up to four parallel-connected IGBT modules.
The master is equipped with a fiber-optic interface and global fault management. In master/slave configurations, the slaves are connected to the master via a bus cable which distributes the common command signal and the secondary-side supply voltages from the DC/DC converter. 

The 1SP0340 driver is based on the highly-integrated SCALE-2 chipset which enables high-performance, complete and extremely-compact single-channel IGBT drivers. 

The SCALE-2 chipset also reduces the component count by 80% when compared to conventional solutions, thus significantly increasing reliability and reducing costs.
1SP0340 drivers are equipped with Dynamic Advanced Active Clamping (DA2C), short-circuit protection, regulated turn-on gate driving voltage and supply-voltage-monitoring. 

Tightly-matched driver versions are available for all mechanically-compatible IGBT modules. Plug-and-play capability enables immediate operation after mounting, and the user needs to invest no effort adjusting or designing-in the driver for a specific application.

Fiber-Optic Interface Options
Fiber-optic links are used to electrically isolate the command and status-feedback signals.

For details, please check the product documentation.

Power supply and electrical isolation

In contrast to other SCALE-2 plug-and-play drivers, the 1SP0340 driver is modular, so the driver card and power supply (ISO5125I DC/DC converter) are two separate units. This means that any driver that has been developed to match a specific IGBT module can be used for any required isolation specification. Only the separate power supply (ISO5125I) must be selected to match the specific application. A further benefit is that drivers for 4.5 kV IGBTs can be implemented in 2-level, 3-level and multi-level inverter topologies. 

The driver is mounted directly onto the IGBT module using three screws. The separate power supply unit is attached close by the IGBT. For parallel-connected drivers, only one power supply is needed per switch.

명세서

명세서
지원되는 모듈 CM1500HC-90XA
최대 스위칭 주파수 10.00 kHz
IGBT 전압 등급 4500 V
기술 SCALE-2
출력 전력 / 채널-최대 2.80 W
인터페이스 유형 전기
IGBT 제조업체 Mitsubishi/Powerex
채널 수 1
게이트 피크 전류 (최대) +35 A
상품 유형 회로 기판
Product Sub-Type 플러그 앤 플레이 드라이버
지원되는 모듈 유형 IGBT
메인 / 주변 주변
지원되는 토폴로지
2단계 전압 소스
3단계 NP 클램프 - 유형 1
3단계 NP 클램프 - 유형 2
다단계 NP 클램프
보호 기능
동적 고급 능동 클램핑
과전압
저전압 (2차측)
드라이브 모드 직접 독립형
IGBT에 대한 연결 유형 Direct
논리 입력 전압 15
공급 전압 (일반) 25.00 V
게이트 턴온 전압 +15.00 V
게이트 턴 오프 전압 --10.00 V
전압 - DC 링크 꺼짐 상태, 60 초 3550.00 V
시간 - 출력 상승 10.00 ns
시간 - 출력 하락 25.00 ns
게이트 피크 전류 (최소) -35