![SCALE-2 1SP0340 Module SCALE-2 1SP0340 Module](/sites/default/files/images/products/PI-1600x1200%402x_SCALE-2-1SP0340.png)
1SP0340D2S0C-FZ1200R45HL3
Single-Channel SCALE-2 Plug-and-Play for 4.5kV IGBTs, Direct Paralleling Supported by Master/Slave Drivers
์ ํ ์์ธ ์ ๋ณด
The new 1SP0340 SCALE-2 Plug-and-Play driver is specifically designed for the reliable and safe driving of 130 x 140 mm and 190 x 140 mm IGBT modules with 6000 V isolation voltage and 4.5 kV blocking voltage. It is optimized for high-reliability applications in the rail industry.
The driver concept relies on a master/slave principle that enables parallel-connected IGBT modules to be operated safely. The master (1SP0340V) can be used as a stand-alone driver without slave to drive a single IGBT module, or with up to three slaves (1SP0340D) to drive up to four parallel-connected IGBT modules.
The master is equipped with a fiber-optic interface and global fault management. In master/slave configurations, the slaves are connected to the master via a bus cable which distributes the common command signal and the secondary-side supply voltages from the DC/DC converter.
The 1SP0340 driver is based on the highly-integrated SCALE-2 chipset which enables high-performance, complete and extremely-compact single-channel IGBT drivers.
The SCALE-2 chipset also reduces the component count by 80% when compared to conventional solutions, thus significantly increasing reliability and reducing costs.
1SP0340 drivers are equipped with Dynamic Advanced Active Clamping (DA2C), short-circuit protection, regulated turn-on gate driving voltage and supply-voltage-monitoring.
Tightly-matched driver versions are available for all mechanically-compatible IGBT modules. Plug-and-play capability enables immediate operation after mounting, and the user needs to invest no effort adjusting or designing-in the driver for a specific application.
Fiber-Optic Interface Options
Fiber-optic links are used to electrically isolate the command and status-feedback signals.
For details, please check the product documentation.
Power supply and electrical isolation
In contrast to other SCALE-2 plug-and-play drivers, the 1SP0340 driver is modular, so the driver card and power supply (ISO5125I DC/DC converter) are two separate units. This means that any driver that has been developed to match a specific IGBT module can be used for any required isolation specification. Only the separate power supply (ISO5125I) must be selected to match the specific application. A further benefit is that drivers for 4.5 kV IGBTs can be implemented in 2-level, 3-level and multi-level inverter topologies.
The driver is mounted directly onto the IGBT module using three screws. The separate power supply unit is attached close by the IGBT. For parallel-connected drivers, only one power supply is needed per switch.
๋ช ์ธ์
์ง์๋๋ ๋ชจ๋ | FZ1200R45HL3 |
์ต๋ ์ค์์นญ ์ฃผํ์ | 3.50 kHz |
IGBT ์ ์ ๋ฑ๊ธ | 4500 V |
๊ธฐ์ | SCALE-2 |
์ถ๋ ฅ ์ ๋ ฅ / ์ฑ๋-์ต๋ | 2.80 W |
์ธํฐํ์ด์ค ์ ํ | ์ ๊ธฐ |
IGBT ์ ์กฐ์ ์ฒด | Infineon |
์ฑ๋ ์ | 1 |
๊ฒ์ดํธ ํผํฌ ์ ๋ฅ (์ต๋) | +35 A |
์ํ ์ ํ | ํ๋ก ๊ธฐํ |
Product Sub-Type | ํ๋ฌ๊ทธ ์ค ํ๋ ์ด ๋๋ผ์ด๋ฒ |
์ง์๋๋ ๋ชจ๋ ์ ํ | IGBT |
๋ฉ์ธ / ์ฃผ๋ณ | ์ฃผ๋ณ |
์ง์๋๋ ํ ํด๋ก์ง |
2๋จ๊ณ ์ ์ ์์ค
3๋จ๊ณ NP ํด๋จํ - ์ ํ 1
3๋จ๊ณ NP ํด๋จํ - ์ ํ 2
๋ค๋จ๊ณ NP ํด๋จํ
|
๋ณดํธ ๊ธฐ๋ฅ |
๋์ ๊ณ ๊ธ ๋ฅ๋ ํด๋จํ
๊ณผ์ ์
์ ์ ์ (2์ฐจ์ธก)
|
๋ฑ๊ฐ ์ฝํ ? | ์ |
๋๋ผ์ด๋ธ ๋ชจ๋ | ์ง์ ๋ ๋ฆฝํ |
IGBT์ ๋ํ ์ฐ๊ฒฐ ์ ํ | Direct |
๋ ผ๋ฆฌ ์ ๋ ฅ ์ ์ | 15 |
๊ณต๊ธ ์ ์ (์ผ๋ฐ) | 25.00 V |
๊ฒ์ดํธ ํด์จ ์ ์ | +15.00 V |
๊ฒ์ดํธ ํด ์คํ ์ ์ | --10.00 V |
์ ์ - DC ๋งํฌ ๊บผ์ง ์ํ, 60 ์ด | 3550.00 V |
์๊ฐ - ์ถ๋ ฅ ์์น | 10.00 ns |
์๊ฐ - ์ถ๋ ฅ ํ๋ฝ | 25.00 ns |
๊ฒ์ดํธ ํผํฌ ์ ๋ฅ (์ต์) | -35 |