PI Forums

Hi, We are using the LNK306DGTL in our project to generate a 5V, 250mA output and using this power to drive relays and microcontroller During prototype testing, we observed audible noise coming from the power circuitry. I’ve attached the schematic for your reference. Could you please review it and let

Row 126 -Idc=1.5a Row 133 -Rdc(100)=29.33m-ohm Row 134 -Ploss both secondary =0.53W BUT!!! Ploss both secondary=1.5^2*0.02933*2=0.132W WHERE IS THE ERROR ?

Hello there, We have been working on TOP267 and designed a 24V/5A SMPS using ETD Core, at load it is tuned to 24VDC at half load it goes down to 22V, and at full load further decreases to 21V. Is there any way we can reduce this difference a drop

Please suggest PnP gate driver board for FF300R07ME4_B11 and FF450R07ME4. The boards should have operating temperature rating from -40 deg. C to +85 Deg. C.

I have used PI Expert online to design using the TNY286PG for an output of 12V, 1A. I am not sure how to send the design file online, but I made some changes of capacitor/resistor values, on the snubbing network input to the Drain. The suggested part numbers for the

hello there, We have been manufacturing 24V/2A SMPS, and we need to add an auto-cut while charging batteries. We are planning to tune the SMPS to 26V and need to add an auto-cut Warm Regards

I am referring to AN82 to design a flyback converter with 15 W output , i have selected TNY286 from the application note, at step7 in the design steps for continuous mode operation (page number 50) i am getting KRP as negative value Is this ok, can i move forward

Hi, We're using the 2SC0435T2F1-17 SCALE-2+ driver to control two IGBTs in our system. We've been using this part in production for a while without any issues. However, on a recent power-up, one of the boards experienced a failure — the IC on one channel visibly burned (photo attached; affected

Hi, We are using TFS7707H for generating 12V@15A as a supply for our telecom products. We are facing field failure of IC TFS7707H (IC blast). We are not able to find the root cause of failure of this IC tfs7707h. We suspect the wrong selection of series resistor R2 and

Hi, I am using CPZ1061 instead of CPZ1075 in a design suggested in DER-943, as CPZ1075 wasn't readily available in my part of world. While testing I found that at the first time powering up the SMPS starts OK, gives desire output and works fine. But as soon as I

Hi I have recently published my new article to INN369the x application. The target was the more simple design with the planar transformer. (the additional winding for INN3xxx will not be necessary). https://www.researchgate.net/publication/389701973_The_effective_replacement_of_the_bias_winding-coil regards zbyno

Hi, I'm working on a project and I'm using 2SC0115T2A0-12 for driving an H-bridge ACDC Active front end. I'm following all the recommendations given in the application notes. The sinusoidal PWM of 1kHz that I'm using, when I check on the input to the gate driver is very clean and

Hello there, We have been manufacturing this 24V/5A SMPS for a very long time having an input voltage of 195-285 VAC but one of our clients needs the same in 85-265 VAC please suggest ways to convert this into a universal Input SMPS. We are ok with the new transformer

Hi, Can someone help me to choose Rg,n and Rg,off resistors on 2SP0115T2A0 for Infineon FF300R12ME7_B11

Hi, My company are using LNK3202 as a HV Buck. UK Mains down to 12V. They have accidentally put C3 (below on page 5) as 220nF MLCC instead of a 10uF electrolytic. They have shipped many products like this by accident. What could be the possible effects? Page 5 schem

We built a 5V PSU on TNY286KG-TL following the Application Note AN-82 TinySwitch-4 Family Design Guide. It works fine, but has very slow transient response. The recommended combination of CFB2 and RS1 places the crossover frequency very low (even much lover for higher output voltages), which results in poor transient

Hello, I wound a transformer for a LYT5228D circuit, according to the ACDC_LYTSwitch5_Buck_051424; Rev.2.0 design spreadsheet and its associated magnetics designer. I wound it exactly according to the spreadsheet (see attached a screenshot of the relevant sections of the spreadsheet). However, it causes strong radiated emissions as measured with our

Hi， 1）Can I change the number of valleys in QR mode to start conduction? 2）How do I change from DCM mode to CCM mode? Need to change the parameters of the load? Regards, Jun Yi!

I can not access TopSwitch II spreedsheet for a new design. Has someone a copy for that spreadsheet? I know Power Int is suggesting new models for new designs but my client insist to have a product using Top226yn. thanks in advance...

AC/DC converter for a controller of electrical appliances. 6-8 Watt, 12V DC output, Isolated, input voltage 90-265V, Breakdown voltage 750-900V. Low component count. Open frame.